Wavetek 39A Specifikace stáhnout pdf (Strana 32)

User Manual 301/302

Figure 3-3 Adjusting Standard Waveform types and Parameters

Select the Output tab, and turn on each channel output by selecting

Channel on for each channel. Turn on the channel SYNC output, if

required.

Figure 3-4 Turning on Outputs

If the above commands are executed correctly, a square waveform

will be seen on your oscilloscope at the channel A and B outputs

connector.

Configuring the Instrument

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 136 137

WARRANTY 3
Exclusion of Other Warranties 3
DECLARATION OF CONFORMITY 4
Model 301 and Model 302 4
SAFETY PRECAUTIONS 5
Table of Contents 6
301/302 User Manual 10
Table of Figures 10
Getting Started 12
Introduction 13
Input and Output 16
Connectors 16
Operating Modes 17
Continuous Mode 18
Triggered Mode 18
Burst Mode 18
Gated Mode 18
Output Type 18
Standard (Fixed) 19
Waveforms 19
Arbitrary (User) 19
Sequenced 20
Output State 22
Front Panel 22
Indicators 22
Programming The 22
Model 301/302 22
CONFIGURING The INSTRUMENT 23
Performance 24
Requirements 24
Preparation For 26
Logical Address 26
Selection 26
Installation 27
Bench Operation 27
Rack Mounting 27
USING The INSTRUMENT 28
Power On/Reset 29
Defaults 29
Programming the 29
:VOLTage 2; 30
÷ 2) ≤ 5 30
Controlling the 31
301/2 Using 31
WaveWiz 31
Controlling 33
Instrument 33
Functions 33
Using the APPLy 33
Selecting the 36
Active Channel 36
Enabling the Main 37
Selecting an 38
Selecting a 39
Standard 39
Function Shape 39
Changing the 42
Frequency and 42
Sample Clock 42
External SCLK 43
Output Amplitude 44
Filter Type 45
Operating Mode 46
Selecting the Trigger 49
Using the Internal 50
Trigger Generator 50
Assigning the 52
Source For The 52
SYNC Output 52
Generating 53
Arbitrary 53
What Are 54
Waveforms? 54
Arbitrary Memory 55
Management 55
Loading Arbitrary 56
Reversing Byte 58
Using WaveWiz to 59
Generate 59
Using Equation 62
Editor to Generate 62
User Manual 301/302 68
Configuring the Instrument 68
Fast Binary 72
Sequence Table 72
Download 72
Selecting active 74
Sequence 74
Running 75
Sequences 75
Using WaveWiz 75
Advance 77
Advance Source 78
Sequences with 79
Sequences with 80
Adjusting Phase 84
Offset Between 84
Channels 84
Amplitude 86
Modulation 86
System-Related 86
SCPI Commands 87
SCPI COMMAND REFERENCE 89
Query Response 90
SCPI Command Reference 91
Subsystem 106
INSTrument 110
Trigger 111
IEEE-STD-488.2 119
Commands and 119
Registers 120
The SCPI Status 120
The Status Byte 121
Register (STB) 121
Generation 122
Standard Event 124
Status Register 124
Status Enable 125
Register (ESE) 125
Error Messages 125
Device-Specific 128
Commands 128
Appendix A SPECIFICATIONS 130
Triangle 131
Pulse/Ramp 131
ARBITRARY WAVEFORMS 132
SEQUENCED SEQUENCES 133
OUTPUTS (CHANNELS A & B) 134

Komentáře k této Příručce

Žádné komentáře

Wavetek 39A Specifikace Strana 32

Komentáře k této Příručce